PCB[edit]
-
Factory JAMMA adapter
-
PCB
PLD's[edit]
Common[edit]
| PLD Information | Credits | Download | View | |||||
|---|---|---|---|---|---|---|---|---|
| Dump Method | Target Device | Location | ID | Status | Creator(s) | Tester(s) | Files | Pictures |
| Undumped | U72 | 02-01-02 | 
| |||||
| Undumped | U71 | 02-02-01 | 
| |||||
| Undumped | U85 | 02-03-01 | 
| |||||
| Undumped | U90 | 02-12-01 | 
| |||||
| Bruteforced | GAL16V8 | U68 | 02-13-01 | Tested | DogP | DogP | ZIP | 
|
| Undumped | U39 | 02-15-01 | 
| |||||
| Undumped | U40 | 02-16-01 | 
| |||||
| Undumped | U67 | 02-20-01 | 
| |||||
| Bruteforced | GAL16V8 | U91 | 02-21-01 | Tested | DogP | DogP | ZIP | 
|
| Undumped | U106 | 02-22-01 | 
| |||||
| Undumped | U6 | 02-23-01 | 
| |||||
Factory JAMMA Adapter[edit]
| PLD Information | Credits | Download | View | |||||
|---|---|---|---|---|---|---|---|---|
| Dump Method | Target Device | Location | ID | Status | Creator(s) | Tester(s) | Files | Pictures |
| Recreated | GAL16V8 | U3 | 02-28-01 | Tested | DogP | DogP | ZIP | |
Joystick Version[edit]
| PLD Information | Credits | Download | View | |||||
|---|---|---|---|---|---|---|---|---|
| Dump Method | Target Device | Location | ID | Status | Creator(s) | Tester(s) | Files | Pictures |
| Bruteforced | GAL16V8 | U75 | 02-24-01 | Tested | DogP | DogP | ZIP | 
|
| Bruteforced | GAL16V8 | U76 | 02-25-01 | Tested | DogP | DogP | ZIP | 
|
| Bruteforced | GAL16V8 | U77 | 02-26-01 | Tested | DogP | DogP | ZIP | 
|
| Bruteforced | GAL16V8 | U78 | 02-27-01 | Tested | DogP | DogP | ZIP | 
|
Note: To use the joystick PALs on Ataxx, the ROM must support it (Rev 5 does, Rev 1 doesn't, others are untested), and the Ataxx edge connector pin 'Y' must be connected to GND. DogP has confirmed the factory JAMMA adapter has this pin connected to GND via a 0 ohm resistor (see picture)
Trackball Version[edit]
| PLD Information | Credits | Download | View | |||||
|---|---|---|---|---|---|---|---|---|
| Dump Method | Target Device | Location | ID | Status | Creator(s) | Tester(s) | Files | Pictures |
| Recreated | GAL16V8 | U75 | 02-08-01 | Tested | DogP | DogP | ZIP | 
|
| Recreated | GAL16V8 | U76 | 02-09-01 | Tested | DogP | DogP | ZIP |
|
| Recreated | GAL16V8 | U77 | 02-10-01 | Tested | DogP | DogP | ZIP |
|
| Recreated | GAL16V8 | U78 | 02-11-01 | Tested | DogP | DogP | ZIP |
|
Note: To use the trackball PALs on Ataxx, the Ataxx edge connector pin 'Y' must NOT be connected to GND, at least when using the newer ROM revision(s). The factory JAMMA adapter likely has this pin connected to GND for use with the joystick PALs.